songmother1

Peugeot 208 Key Replacement Peugeot 208 key replacement is best left to experienced auto locksmiths with the right equipment and know-how. They can design and program keys quicker and more efficiently than dealers. If the key fob stopped locking or unlocking your doors it could be due to a dead coin battery. There are also other reasons why the key may be malfunctioning. Dead Coin Battery A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking and will not start the engine. If this is the situation, you'll need make use of the backup starting procedure which is explained in the owner's manual to your vehicle. Another reason why the 208 won't start is that the spark plugs are worn down. The spark plugs are responsible for sparking the fuel which starts the engine. They have a limited life span. They'll eventually degrade when they aren't used enough. There is a straightforward solution to this issue. The best way to solve this issue is to determine the voltage of your car battery using a multimeter. If it's lower than 11.5 volts and you are not satisfied, then it is time to replace it. If the battery has corroded it is essential to clean its contacts. You can do this by lifting the rubber covers covering the two terminals of the battery and using wire brushes to clean any corroded parts of the battery. It is then time to reconnect the cables for the positive and negative poles. Water Damage If your 208 won't start and the battery isn't running, then make sure that the spark plugs are in good working order. You may find that they are simply too dirty and don't spark. This is easily fixed by cleaning the spark plugs in a workshop. Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This guarantees that only the right key is able to start the engine. If the chip in the Peugeot key is damaged, it will not transmit the correct signal to the vehicle. This is a very common issue that is caused by water damage. This is a common issue in colder climates where the vehicle has been exposed to rain or snow. In this case, contact a trusted locksmith who has the tools and equipment required to reprogram the key. They'll also have the latest technology and machinery required to create the Peugeot smart key. The process should take no more than 15 minutes. Contacts to the battery are not working properly. Peugeot changed from the old carbon-encased transponder chips to an entirely new kind of chip that utilizes electronic components on circuit boards. The new system is great when it's new, however the circuit boards wear out over time and cease to function properly. This can stop the immobiliser from activating so the vehicle won't start. Contact an Peugeot specialist, or a locksmith if this is the situation. A common problem is when the battery in the key fob starts to die. This causes the blade of the key to stop feeding into your lock. A locksmith from your vehicle can replace the battery and cut a fresh blade for you, this is normally a quick fix. Faulty Receiver Module If your Peugeot key fob was not working after dropping it on the floor, getting exposed to a sudden rain or accidentally washing it, it could be due a malfunctioning receiver module. The receiver is responsible for sending radio frequency signals to the onboard computer that controls the central locking system in your Peugeot vehicle. The key fob itself has rubber seals which prevent water from reaching the electronic chip inside. The chip can be damaged by water if it is exposed to the water for an extended period of period of. The high salt content in the ocean water or pool could cause damage to the key fob if it is submerged. If repair fob isn't working You'll need the module replaced. This is only performed by a professional auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by an unique immobilizer system that requires the correct programming to start the engine. This is why you must go with a knowledgeable Peugeot locksmith to take on the job of designing and programming an appropriate replacement. Computer malfunctioning on-board The computer on board of your Peugeot is responsible for various features in your car, including airbags and power windows. If something is wrong with these systems, it'll typically display a code indicating the problem. This code is saved in the system and stays there until the issue has been resolved. This could mean that the on-board computers to be replaced. The most frequent cause for the warning light for airbags to turn on is corrosion or loose connections within the sensor. This can be caused by wear and tear, aging, or exposure to moisture and salt. This issue should be addressed as soon you can, since an airbag that is malfunctioning could be dangerous in the event of an accident. If your Peugeot is showing a card that is not being detected error, the battery inside the key fob could be weak or dead. This will stop the key fob from sending a signal to disarm the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob and then trying to start your vehicle. If this doesn't work it is because the battery of the key must be replaced.